All Burner Controls
Fireye provides a variety of burner control flame safeguard and combustion controls. Our BurnerPRO™, BurnerLogix™, Flame-Monitor™ and MicroM families provide safe and reliable light off of packaged burners used on commercial and industrial boilers as well as direct fired makeup air units and commercial hot water heaters.
Burner Controls Subcategories
The Fireye BurnerLogixTM System is a microprocessor based burner management control system designed to provide the proper burner sequencing, ignition and flame monitoring protection onautomatically ignited oil, gas, and combination fuel burner […]
BurnerPRO Flame Safeguard The BurnerPRO™ provides the proper burner sequencing, ignition and continuous flame monitoring for commercial heating and process equipment firing oil and gas fuels. BurnerPRO Flame Safeguard (BP110UVF/BP230UVF) Contr […]
D-Series 70D40 and 70D41 Burner Control Fireye Series D10, D20 and D30 burner management controls provide ignition and main flame failure protection for automatically ignited oil and gas burners. Plug-in Amplifier Modules permit the selection […]
The Fireye® FLAME-MONITOR™ System is a microprocessor based burner management control system designed to provide the proper burner sequencing, ignition and flame monitoring pro-tection on automatically ignited oil, gas, and combination fuel bu […]
Fireye Flame Scanners provides a variety of UV and IR flame scanners that accurately detect the presence or absence of flame in a combustion chamber and some provide both self-check and non-self check capabilities.
The inTouch Wireless Monitoring System provides continuous monitoring for up to 10 Flame-Monitor, MicroM and/or BurnerLogix flame safeguard controls. The inTouch System provides 4 dry-contact andAC power inputs. In the event of a lockout or co […]
Fireye® Modular M-Series II Flame Safeguard Controls are compact, modular burner management systems. They are designed to provide automatic ignition and continuous flame monitoring for commercial sizes of heating and process burners that use g […]
Designed to provide automatic ignition and continuous flame monitoring, the M4RT1/M4RT24 is meant for commercial-sized heating and process burners that use gaseous fuels. The M4RT1/M4RT24 control incorporates a safety checking circuit that is […]
Burner Controls Components
MEP437 Programmer, Valve proof of closure, selectable purge, PTFI timing, intermittent or interrupted, recycle / non‐recycle operation, reset by power interruption of manual reset.
MEP696 Programmer, provides selectable PTFI, selectable baud rate, and selectable recycle / non‐recycle operation. For use with MEC320TS chassis only.
MEP697 Programmer Selectable TFI timing, purge timing, post purge, prove open at start, and recycle / non‐recycle on flame fail. Includes 5 sec pilot proving, early spark termination, 10 sec MTFI, and interrupted pilot.
MEUV1 UV amp, 0.8 sec FFRT. Use with UV1, UV2, 45UV3.
MEUV4 UV amp, 3 sec FFRT. Use with UV1, UV2, 45UV3.
MEUVS1 UV self check amp, 0.8 sec FFRT. Use with 45UV5‐1008, ‐1009.
MEUVS4 UV self check amp, 3 sec FFRT. Use with 45UV5‐1008, ‐1009.
MEUV4 UV amp, 3 sec FFRT. Use with UV1, UV2, 45UV3.
MERT4 Flame rect amp. 3 sec FFRT. Use with 69ND, 45CM.
MEIR1 Infrared amp, 0.8 sec FFRT. Use with 48PT2 scanner.
MEIR4 Infrared amp, 3 sec FFRT. Use with 48PT2 scanner.
MECD1 Cadmium sulfide amp, 0.8 sec FFRT. Use with C554A scanner.
MECD4 Cadmium sulfide amp, 3 sec FFRT. Use with C554A scanner.
MEP237 Programmer, Selectable recycle/non‐recycle function, TFI timing, purge timing, post purge, prove open at start. Provides 0.30 second flame failure response time, for use with Phoenix and InSight flame scanner and MEDC2 amplifier.
